Abstract Band structure by design in 2D layered semiconductors is highly desirable, with the goal to acquire the electronic properties of interest through the engineering of chemical composition, structure, defect, stacking, or doping. For atomically thin transition metal dichalcogenides, substitutional doping with more than one single type of transition metals is the task for which no feasible approach is proposed. Here, the growth of WS2 monolayer is shown codoped with multiple kinds of transition metal impurities via chemical vapor deposition controlled in a diffusion-limited mode. Multielement embedment of Cr, Fe, Nb, and Mo into the host lattice is exemplified. Abundant impurity states thus generate in the bandgap of the resultant WS2 and provide a robust switch of charging/discharging states upon sweep of an electric filed. A profound memory window exists in the transfer curves of doped WS2 field-effect transistors, forming the basis of binary states for robust nonvolatile memory. The doping technique presented in this work brings one step closer to the rational design of 2D semiconductors with desired electronic properties.

Abstract A heterobimetallic corrole complex, comprising oxygen reduction reaction (ORR) active non-precious metals Co and Fe with a corrole-N4 center (PhFCC), is successfully synthesized and used to prepare a dual-atom molecular catalyst (DAMC) through subsequent low-temperature pyrolysis. This low-temperature pyrolyzed electrocatalyst exhibited impressive ORR performance, with onset potentials of 0.86 and 0.94 V, and half-wave potentials of 0.75 and 0.85 V, under acidic and basic conditions, respectively. During potential cycling, this DAMC displayed half-wave potential losses of only 25 and 5 mV under acidic and alkaline conditions after 3000 cycles, respectively, demonstrating its excellent stability. Single-cell Nafion-based proton exchange membrane fuel cell performance using this DAMC as the cathode catalyst showed a maximum power density of 225 mW cm−2, almost close to that of most metal–N4 macrocycle-based catalysts. The present study showed that preservation of the defined CoN4 structure along with the cocatalytic Fe–Cx site synergistically acted as a dual ORR active center to boost overall ORR performance. The development of DAMC from a heterobimetallic CoN4-macrocyclic system using low-temperature pyrolysis is also advantageous for practical applications.

The thickness of transition metal dichalcogenides (TMDs) plays a key role in enhancing their photocatalytic CO2 reduction activity. However, the optimum thickness of the layered TMDs that is required to achieve sufficient light absorption and excellent crystallinity has still not been definitively determined. In this work, ultra-thin molybdenum disulfide films (MoS2TF) with 25 nm thickness presented remarkable photocatalytic activity, and the product yield increased by about 2.3 times. The photocatalytic mechanism corresponding to the TMDs’ thickness was also proposed. This work demonstrates that the thickness optimization of TMDs provides a cogent direction for the design of high-performance photocatalysts.

The quest of earth-abundant bifunctional electrocatalysts for highly efficient oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is essential for clean and renewable energy systems. Herein, directed by the experimental analysis, we demonstrate layered nickel lithium phosphosulfide (NiLiP2S6) crystal as a highly efficient water-splitting catalyst in alkaline media. With strained lattice due to stacked layers as observed by TEM and electronic structure analysis performed by XPS showed mixed Ni2+,3+ oxidation states induced by addition of Li as a cation, NiLiP2S6 displays excellent OER (current density of 10 mA cm–2 showed an overpotential of 303 mV vs. RHE and a Tafel slope of 114 mV dec–1) and HER activity (current density of −10 mA cm–2 showed an overpotential of 184 mV vs. RHE and a Tafel slope of 94.5 mV dec–1). Finally, an alkaline media was employed to demonstrate the overall water splitting using NiLiP2S6 as both the anode and the cathode, which attained a 50 mA cm−2 current density at 1.68 V. This bimetallic phosphosulfide, together with long-term stability and enhanced intrinsic activity, shows enormous potential in water splitting applications.

n/a

Lithium metal anodes form a dendritic structure after cycling which causes an internal short circuit in flammable electrolytes and results in battery fires. Today's separators are insufficient for suppressing the formation of lithium dendrites. Herein, we report on the use of mesoporous silica thin films (MSTFs) with perpendicular nanochannels (pore size ∼5 nm) stacking on an anodic aluminum oxide (AAO) membrane as the MSTF⊥AAO separator for advancing Li metal batteries. The nanoporous MSTF⊥AAO separator with novel inorganic structures shows ultra-long term stability of Li plating/stripping in Li–Li cells at an ultra-high current density and capacity (10 mA cm−2 and 5 mA h cm−2). A significant improvement over the state-of-the-art separator is evaluated based on three performance indicators, e.g. cycle life, current density and capacity. In Li–Cu cells, the MSTF⊥AAO separator shows a coulombic efficiency of >99.9% at a current density of 10 mA cm−2 for more than 250 h of cycling. The separator gives improved rate capability in Li–LiFePO4 (LFP) batteries. The excellent performance of the MSTF⊥AAO separator is due to good wetting of electrolytes, straight nanopores with negative charges, uniform Li deposition and blocking the finest dendrite.

Most chemical vapor deposition methods for transition metal dichalcogenides use an extremely small amount of precursor to render large single-crystal flakes, which usually causes low coverage of the materials on the substrate. In this study, a self-capping vapor-liquid-solid reaction is proposed to fabricate large-grain, continuous MoS2 films. An intermediate liquid phase-Na2Mo2O7 is formed through a eutectic reaction of MoO3 and NaF, followed by being sulfurized into MoS2. The as-formed MoS2 seeds function as a capping layer that reduces the nucleation density and promotes lateral growth. By tuning the driving force of the reaction, large mono/bilayer (1.1 mm/200 μm) flakes or full-coverage films (with a record-high average grain size of 450 μm) can be grown on centimeter-scale substrates. The field-effect transistors fabricated from the full-coverage films show high mobility (33 and 49 cm2 V−1 s−1 for the mono and bilayer regions) and on/off ratio (1 ~ 5 × 108) across a 1.5 cm × 1.5 cm region.

BiCuTeO is a promising thermoelectric material owing to its intrinsically low thermal conductivity and high carrier concentration. This study investigated the influence of stoichiometric oxygen deficiencies on the thermoelectric performance of BiCuTeO. Bulk BiCuTeO1−x (0.16 ≥ x) samples were prepared by a conventional solid state reaction and pelleted by hot pressing. Synchrotron X-ray diffraction, electron probe X-ray microanalysis, scanning electron microscopy, and transmission electron microscopy characterized the samples. A maximum value of 1.06 was achieved for the dimensionless figure of merit ZT at 673 K for BiCuTeO0.88, which is approximately 49% better than the current maximal ZT value for BiCuTeO. The power factor was noticeably improved owing to increases in the electrical conductivity and Seebeck coefficient. Moreover, the optimal oxygen deficiency could introduce nanoparticles, resulting in reduced thermal conductivity. The findings will be important for the future development of metal oxide thermoelectric materials for use in practical thermoelectric devices.

Recent advances in nanotechnology, especially the development of integrated nanostructured materials, have offered unprecedented opportunities for photocatalytic CO2 reduction. Compared to bulk semiconductor photocatalysts, most of these nanostructured photocatalysts offer at least one advantage in areas such as photogenerated carrier kinetics, light absorption, and active surface area, supporting improved photochemical reaction efficiencies. In this review, we briefly cover the cutting-edge research activities in the area of integrated nanostructured catalysts for photochemical CO2 reduction, including aqueous and gas-phase reactions. Primarily explored are the basic principles of tailor-made nanostructured composite photocatalysts and how nanostructuring influences photochemical performance. Specifically, we summarize the recent developments related to integrated nanostructured materials for photocatalytic CO2 reduction, mainly in the following five categories: carbon-based nano-architectures, metal–organic frameworks, covalent-organic frameworks, conjugated porous polymers, and layered double hydroxide-based inorganic hybrids. Besides the technical aspects of nanostructure-enhanced catalytic performance in photochemical CO2 reduction, some future research trends and promising strategies are addressed.

The conversion of CO2 into hydrocarbon fuels via the photocatalytic reaction route is considered a potential strategy to concurrently address serious energy crisis and greenhouse gas emission problems. Nevertheless, the generation of long-chain hydrocarbon products (Cn, n ≥ 2) from the visible-light-reactive photocatalytic CO2 reduction has also been considering a contemporary challenge. Herein, we indicate that Ag nanoparticles (Ag NPs) loaded gC3N4/ZnO nanorods heterojunction (Ag-gC3N4/ZnO NRs abbreviation) has extended photoactive range and enhanced specific surface area. The combination of Ag NPs and gC3N4/ZnO NRs significantly enhances photocatalytic CO2 reduction efficiency to form the acetone product. Detail, the acetone production efficiency of Ag-gC3N4/ZnO NRs is 8.4 and 7.5 times higher than pure ZnO NRs and gC3N4/ZnO NRs at the same condition, respectively. This study represents a potential approach toward higher-energy-value hydrocarbons production and greenhouse gas emission mitigation.