Kuei-Hsien Chen

Although hematite (i.e., α-Fe2O3) has been widely investigated in photoelectrochemical water oxidation studies due to its high theoretical photocurrent density, it still suffers from serious surface charge recombination and low photoelectrochemical stability. Here we report an in-situ electrochemical method to form a uniform and ultrathin (i.e., 3–5 nm) passivation layer all over the porosities of the optimized ~3.2% Ti-doped α-Fe2O3 photoanode. We unveil the amorphous and defective nature of the in-situ derived layer assigning to a high concentration of oxygen vacancy and intercalated potassium atoms there, i.e., the formation of Ti/K co-doped defective α-Fe2O3-x. Owing to the efficient passivation of surface states, alleviated surface-potential fluctuations, and low charge-transfer resistance at the interface, photoanodes show an average of ~60% enhancement in the photoelectrochemical performance, applied bias absorbed photon-to-current efficiency of 0.43%, and Faradaic efficiency of ~88%. Moreover, the passivation layer prevents direct contact between the electrode material and electrolyte, resulting in less degradation and outstanding photoelectrochemical stability with photocurrent retention of ~95% after ~100 hours, albeit by performing several successive in-situ electrochemical passivation processes. This work presents an industrially scalable method to controllably engineer the interfaces of semiconductors–electrolytes with precious metal-free defective hematite-based co-catalysts for sustainable photoelectrochemical solar-to-fuel conversion applications.

Abstract Effects of electronic and atomic structures of V-doped 2D layered SnS2 are studied using X-ray spectroscopy for the development of photocatalytic/photovoltaic applications. Extended X-ray absorption fine structure measurements at V K-edge reveal the presence of VO and VS bonds which form the intercalation of tetrahedral OVS sites in the van der Waals (vdW) gap of SnS2 layers. X-ray absorption near-edge structure (XANES) reveals not only valence state of V dopant in SnS2 is ≈4+ but also the charge transfer (CT) from V to ligands, supported by V Lα,β resonant inelastic X-ray scattering. These results suggest V doping produces extra interlayer covalent interactions and additional conducting channels, which increase the electronic conductivity and CT. This gives rapid transport of photo-excited electrons and effective carrier separation in layered SnS2. Additionally, valence-band photoemission spectra and S K-edge XANES indicate that the density of states near/at valence-band maximum is shifted to lower binding energy in V-doped SnS2 compare to pristine SnS2 and exhibits band gap shrinkage. These findings support first-principles density functional theory calculations of the interstitially tetrahedral OVS site intercalated in the vdW gap, highlighting the CT from V to ligands in V-doped SnS2.

In this work, we study the effect of sputtering pressures on the thermoelectric properties of GeTe films. The working pressures were differentiated from 3 to 30 mTorr, and the as-deposited films were annealed at 623 K for 10 min in Ar atmosphere. The results show that the working pressure has a significant effect on the Ge content and crystalline size. The turning trend of the Seebeck coefficient with different sputtering pressures corresponds to the Ge content. The surface morphology of annealed film will change from cracks to voids with increasing sputtering pressure. This behavior can be explained by the growth mechanisms model. The voids and relatively low crystalline size of GeTe films affect to the reduction of the electrical conductivity. In addition, the void content decreased as film thickness was increased. Therefore, controlling the working pressures in the sputtering process and film thickness is important for the thermoelectric performance of GeTe thin film. In our work, we prove that the thermoelectric properties of GeTe films could be optimized effectively by simply tuning different sputtering conditions.

Exploring an efficient platinum group metal (PGM) free electrocatalyst with superior activity and stability for hydrogen evolution reaction (HER) in a wide pH range is desirable for low-cost hydrogen production. Here, we report atomically dispersed cobalt on nitrogen and sulfur co-doped graphene (N-Co-S/G) for HER. Remarkably, the prepared N-Co-S/G electrocatalyst shows a small overpotential of 67.7 mV vs. reversible hydrogen electrode (RHE) at a current density of 10 mA cm−2 and exceptional durability over 100 h at 10 mA cm−2 under acidic conditions. Moreover, we found that the HER activity of N-Co-S/G is close to 20% Pt/C at all pH levels (0–14) and superior activity at high current density (>100 mA cm−2). Experimental and theoretical calculations reveal that the S atom in N-Co-S/G form Co-S bond, resulting new Co-N3S1 active site, which optimizes Gibbs free energy for hydrogen adsorption (∆GH*) close to zero, while water adsorption and dissociation enhanced by S modulation for neutral and basic media HER.

Pharmaceutical drugs' removal from wastewater by photocatalytic oxidation process is considered as an attractive approach and environmentally friendly solution. This report aims to appraise the practical application potential of Ag/g-C3N4/ZnO nanorods toward the wastewater treatment of the pharmaceutical industry. The catalysts are synthesized by straightforward and environmentally-friendly strategies. Specifically, g-C3N4/ZnO nanorods heterostructure is constructed by a simple self-assembly method, and then Ag nanoparticles are decorated on g-C3N4/ZnO nanorods by a photoreduction route. The results show that three commercial drugs (paracetamol, amoxicillin, and cefalexin) with high concentration (40 mg L−1) are significantly degraded in the existence of a small dosage of Ag/g-C3N4/ZnO nanorods (0.08 g L−1). The Ag/g-C3N4/ZnO nanorods photocatalyst exhibits degradation performance of paracetamol higher 3.8, 1.8, 1.3 times than pristine g-C3N4, ZnO nanorods, and g-C3N4/ZnO nanorods. Furthermore, Ag/g-C3N4/ZnO nanorods have an excellent reusability and a chemical stability that achieved paracetamol degradation efficiency of 78% and remained chemical structure of the photocatalyst after five cycles. In addition, the photocatalytic mechanism explanation and comparison of photocatalytic drugs’ degradation ability have also been discussed in this study.

Solar cells based on kesterite Cu2ZnSnSe4 (CZTSe) compounds with earth-abundant elements are highly desirable for the low-cost and high-efficiency production of renewable energy. However, the occurrence of intrinsic defects substantially impairs the photovoltaic properties of CZTSe. Herein, a cation substitution method to control and passivate the defect states in bandgap of kesterite CZTSe by incorporating Ag ions is introduced. Intensity-dependent low-temperature photoluminescence measurements show that Ag incorporation can reduce the density and depth of intrinsic defects in CZTSe. The results reveal that 10% Ag-alloyed CZTSe provides the shallowest defect states and less nonradiative recombination. It is also confirmed by first-principles calculations that Ag incorporation enables the formation and suppresses the beneficial and detrimental defects, respectively. Based on the theoretical results, the observed subband photoluminescence peaks can be assigned to the intrinsic point and cluster defects. The best power conversion efficiency of 10.2% is achieved for the 10% Ag-alloyed CZTSe cell, along with an enhanced open-circuit voltage. These results open up a new avenue for further improving the performances of CZTSe-based device via defect engineering.

Utilization of g-C3N4 as a single photocatalyst material without combination with other semiconductor remains challenging. Herein, we report a facile green method for synthesizing a metal free modified g-C3N4 photocatalyst. The modification process combines four different strategies in a one-pot thermal reaction: non-metal doping, porosity generation, functionalization with amino groups, and thermal oxidation etching. The as-prepared amino-functionalized ultrathin nanoporous boron-doped g-C3N4 exhibited a high specific surface area of 143.2 m2 g−1 which resulted in abundant adsorption sites for CO2 and water molecules. The surface amino groups act as Lewis basic sites to adsorb acidic CO2 molecules, which can also serve as active sites to facilitate hydrogen generation. Besides, the simultaneous use of ammonium chloride as a dynamic gas bubble template along with thermal oxidation etching efficiently boosts the delamination of the g-C3N4 layers to produce ultrathin sheets; this leads to stronger light–matter interactions and efficient charge generation. Consequently, the newly modified g-C3N4 achieved selective gas-phase CO2 reduction into CO with a production yield of 21.95 µmol g-1, in the absence of any cocatalyst. Moreover, a high hydrogen generation rate of 3800 µmol g-1 h-1 and prominent apparent quantum yield of 10.6% were recorded. This work opens up a new avenue to explore different rational modifications of g-C3N4 nanosheets for the efficient production of clean energy.

Cu2ZnSnS4 (CZTS) has demonstrated excellent performance as an anode material for lithium-ion batteries. However, the repeated lithiation and delithiation create a cracking pattern and lead to island formation in the thin-film electrode, resulting in a capacity fading over cycling in lithium-ion batteries (LIB's). In order to control this crack behaviour, we introduce carbon into CZTS thin-films by a hydrothermal method to form CZTS@C composite. CZTS@C significantly reduced the crack pattern formation on the electrode surface as well as improved the conductivity of the CZTS@C electrode. At the early stages of lithiation and delithiation, the volume expansion and contraction of Li–CZTS@C create intra-granular cracking only at the surface level, and it offers a high capacity of about 785 mA h g−1 after 150 cycles at 1000 mA g−1 charging rate, excellent rate capability (942 mA h g−1, 678 mA h g−1 and 435 mA h g−1 at 500 mA g−1, 2000 mA g−1 and 5000 mA g−1), and superior cyclability (925 mA h g−1 even after 200 cycles at 500 mA g−1). The excellent electrochemical performance at high-current rates can be attributed to intra-granular cracking together with carbon coating that provides a short transportation length for both lithium ions and electrons. Moreover, the controlled cracking pattern formation in CZTS@C facilitates faster reaction kinetics, which open up a new solution for the development of high-power thin-film anodes for next-generation LIBs applications.

Tin-based composites are promising anode materials for high-performance lithium-ion batteries (LIBs); however, insufficient conductivity, as well as fatal volume expansion during cycling lead to poor electrochemical reversibility and cycling stability. In this work, we demonstrate the lithium-ion storage behaviors of SnS2 anode material deposited on different electrode supports. The SnS2 grown on 3D hierarchical carbon nanotube-carbon cloth composites (SnS2-CNT-CC) shows superior capacity retention and cycle stability, compared to that on planar Mo sheets and carbon cloth. The specific capacity of SnS2 on Mo, CC, and CNT-CC is around 240, 840, and 1250 g−1, respectively. The SnS2-CNT-CC electrode outperforms in the cyclic performance and rate capability compared to other electrode configurations due to the multi-electron pathway and high surface area derived from 3D hierarchical CNT-CC electrode support. Furthermore, a significant decrease in the charge transfer resistance is observed by utilizing 3D hierarchical CNT-CC electrode support. The use of 3D hierarchical structures as electrode support could be the best alternative to enhance the electrochemical performances for the next generation LIBs.

Abstract A heterobimetallic corrole complex, comprising oxygen reduction reaction (ORR) active non-precious metals Co and Fe with a corrole-N4 center (PhFCC), is successfully synthesized and used to prepare a dual-atom molecular catalyst (DAMC) through subsequent low-temperature pyrolysis. This low-temperature pyrolyzed electrocatalyst exhibited impressive ORR performance, with onset potentials of 0.86 and 0.94 V, and half-wave potentials of 0.75 and 0.85 V, under acidic and basic conditions, respectively. During potential cycling, this DAMC displayed half-wave potential losses of only 25 and 5 mV under acidic and alkaline conditions after 3000 cycles, respectively, demonstrating its excellent stability. Single-cell Nafion-based proton exchange membrane fuel cell performance using this DAMC as the cathode catalyst showed a maximum power density of 225 mW cm−2, almost close to that of most metal–N4 macrocycle-based catalysts. The present study showed that preservation of the defined CoN4 structure along with the cocatalytic Fe–Cx site synergistically acted as a dual ORR active center to boost overall ORR performance. The development of DAMC from a heterobimetallic CoN4-macrocyclic system using low-temperature pyrolysis is also advantageous for practical applications.

The quest of earth-abundant bifunctional electrocatalysts for highly efficient oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is essential for clean and renewable energy systems. Herein, directed by the experimental analysis, we demonstrate layered nickel lithium phosphosulfide (NiLiP2S6) crystal as a highly efficient water-splitting catalyst in alkaline media. With strained lattice due to stacked layers as observed by TEM and electronic structure analysis performed by XPS showed mixed Ni2+,3+ oxidation states induced by addition of Li as a cation, NiLiP2S6 displays excellent OER (current density of 10 mA cm–2 showed an overpotential of 303 mV vs. RHE and a Tafel slope of 114 mV dec–1) and HER activity (current density of −10 mA cm–2 showed an overpotential of 184 mV vs. RHE and a Tafel slope of 94.5 mV dec–1). Finally, an alkaline media was employed to demonstrate the overall water splitting using NiLiP2S6 as both the anode and the cathode, which attained a 50 mA cm−2 current density at 1.68 V. This bimetallic phosphosulfide, together with long-term stability and enhanced intrinsic activity, shows enormous potential in water splitting applications.

Most chemical vapor deposition methods for transition metal dichalcogenides use an extremely small amount of precursor to render large single-crystal flakes, which usually causes low coverage of the materials on the substrate. In this study, a self-capping vapor-liquid-solid reaction is proposed to fabricate large-grain, continuous MoS2 films. An intermediate liquid phase-Na2Mo2O7 is formed through a eutectic reaction of MoO3 and NaF, followed by being sulfurized into MoS2. The as-formed MoS2 seeds function as a capping layer that reduces the nucleation density and promotes lateral growth. By tuning the driving force of the reaction, large mono/bilayer (1.1 mm/200 μm) flakes or full-coverage films (with a record-high average grain size of 450 μm) can be grown on centimeter-scale substrates. The field-effect transistors fabricated from the full-coverage films show high mobility (33 and 49 cm2 V−1 s−1 for the mono and bilayer regions) and on/off ratio (1 ~ 5 × 108) across a 1.5 cm × 1.5 cm region.

BiCuTeO is a promising thermoelectric material owing to its intrinsically low thermal conductivity and high carrier concentration. This study investigated the influence of stoichiometric oxygen deficiencies on the thermoelectric performance of BiCuTeO. Bulk BiCuTeO1−x (0.16 ≥ x) samples were prepared by a conventional solid state reaction and pelleted by hot pressing. Synchrotron X-ray diffraction, electron probe X-ray microanalysis, scanning electron microscopy, and transmission electron microscopy characterized the samples. A maximum value of 1.06 was achieved for the dimensionless figure of merit ZT at 673 K for BiCuTeO0.88, which is approximately 49% better than the current maximal ZT value for BiCuTeO. The power factor was noticeably improved owing to increases in the electrical conductivity and Seebeck coefficient. Moreover, the optimal oxygen deficiency could introduce nanoparticles, resulting in reduced thermal conductivity. The findings will be important for the future development of metal oxide thermoelectric materials for use in practical thermoelectric devices.

Recent advances in nanotechnology, especially the development of integrated nanostructured materials, have offered unprecedented opportunities for photocatalytic CO2 reduction. Compared to bulk semiconductor photocatalysts, most of these nanostructured photocatalysts offer at least one advantage in areas such as photogenerated carrier kinetics, light absorption, and active surface area, supporting improved photochemical reaction efficiencies. In this review, we briefly cover the cutting-edge research activities in the area of integrated nanostructured catalysts for photochemical CO2 reduction, including aqueous and gas-phase reactions. Primarily explored are the basic principles of tailor-made nanostructured composite photocatalysts and how nanostructuring influences photochemical performance. Specifically, we summarize the recent developments related to integrated nanostructured materials for photocatalytic CO2 reduction, mainly in the following five categories: carbon-based nano-architectures, metal–organic frameworks, covalent-organic frameworks, conjugated porous polymers, and layered double hydroxide-based inorganic hybrids. Besides the technical aspects of nanostructure-enhanced catalytic performance in photochemical CO2 reduction, some future research trends and promising strategies are addressed.

The conversion of CO2 into hydrocarbon fuels via the photocatalytic reaction route is considered a potential strategy to concurrently address serious energy crisis and greenhouse gas emission problems. Nevertheless, the generation of long-chain hydrocarbon products (Cn, n ≥ 2) from the visible-light-reactive photocatalytic CO2 reduction has also been considering a contemporary challenge. Herein, we indicate that Ag nanoparticles (Ag NPs) loaded gC3N4/ZnO nanorods heterojunction (Ag-gC3N4/ZnO NRs abbreviation) has extended photoactive range and enhanced specific surface area. The combination of Ag NPs and gC3N4/ZnO NRs significantly enhances photocatalytic CO2 reduction efficiency to form the acetone product. Detail, the acetone production efficiency of Ag-gC3N4/ZnO NRs is 8.4 and 7.5 times higher than pure ZnO NRs and gC3N4/ZnO NRs at the same condition, respectively. This study represents a potential approach toward higher-energy-value hydrocarbons production and greenhouse gas emission mitigation.

Gas-phase photocatalytic reactions to convert carbon dioxide and water into oxygen and hydrocarbons are the foundation of life on earth. However, the efficiency of photosynthesis is relatively low (~1%), which leaves much room for artificial photosynthesis to reach the benchmark of the solar cells (>15%). In this work, carbon implanted SnS2 thin films (C–SnS2) were prepared to study photocatalytic activity and adsorbate-catalyst surface interactions during CO2 photoreduction. The electron density distribution in C–SnS2 and its contribution toward the photogenerated charge transfer process has been analyzed by the angle-dependent X-ray absorption near-edge structure (XANES) study. The C–SnS2 surface affinity toward the CO2 molecule was monitored by in-situ dark current and Raman spectroscopy measurements. By optimizing the dose during ion implantation, SnS2 thin film with 1 wt% carbon incorporation shows 108 times enhancement in the CO2 conversion efficiency and more than 89% product selectivity toward CH4 formation compared with the as-grown SnS2 without carbon incorporation. The improved photocatalytic activity can be ascribed to enhanced light harvesting, pronounced charge-transfer between SnS2 and carbon with improved carrier separation and the availability of highly active carbon sites that serve as favorable CO2 adsorption sites.

Bi doped Mg2Si0.4Sn0.6 had been synthesised in a high energy ball mill followed by compaction using a sintering hot press. The structural and compositional characterization of sintered mass indicated the formation of a highly densified single-phase product. The microstructure of the hot-pressed samples had been critically assessed. Thermoelectric properties were measured between room temperature and 723 K. A decrease in electrical conductivity was found with the increase in temperature but the Seebeck coefficient showed a reverse trend justifying the attainment of degenerate semiconducting behaviour. Meanwhile, the lattice thermal conductivity was subdued to 1.5 W/mK at 623 K. However, the highest zT value of 0.8 was achieved at 723 K. Moreover, the detailed X-ray photoelectron spectroscopic analysis was carried for the determination of binding energy of the constituent elements in the experimental alloy; it also provided the correct estimation of atomic percentage of the concerned elements. The Raman spectrum revealed a shift in F2g peak with respect to that of Mg2Sn and Mg2Si in correspondence with the composition of the synthesised alloy. The synthesised alloy showed micro and nano hardness of 3.7 and 4.03 GPa respectively, which implies that good mechanical strength could be achieved in the synthesised alloy.

In addition to the Ge-vacancy control of GeTe, the antimony (Sb) substitution of GeTe for the improvement of thermoelectric performance is explored for Ge1−xSbxTe with x = 0.08–0.12. The concomitant carrier concentration (n) and the aliovalent Sb ion substitution led to an optimal doping level of x = 0.10 to show ZT ∼ 2.35 near ∼800 K, which is significantly higher than those single- and multi-element substitution studies of the GeTe system reported in the literature. In addition, Ge0.9Sb0.1Te demonstrates an impressively high power factor of ∼36 μW cm−1 K−2 and a low thermal conductivity of ∼1.1 W m−1 K−1 at 800 K. The enhanced ZT level for Ge0.9Sb0.1Te is explained through a systematic investigation of micro-structural change and strain analysis from room temperature to 800 K. A significant reduction of lattice thermal conductivity (κlat) is identified and explained by the Sb substitution-introduced strained and widened domain boundaries for the herringbone domain structure of Ge0.9Sb0.1Te. The Sb substitution created multiple forms of strain near the defect centre, the herringbone domain structure, and widened tensile/compressive domain boundaries to support phonon scattering that covers a wide frequency range of the phonon spectrum to reduce lattice thermal conductivity effectively.

Photocatalytic water splitting is a promising way to produce hydrogen fuel from solar energy. In this regard, the search for new photocatalytic materials that can efficiently split water into hydrogen is essential. Here, using first-principles simulations, we demonstrate that the dual-defective SnS2 (Ni-SnS2-VS), by both single-atom nickel doping and sulfur monovacancies, becomes a promising two-dimensional photocatalyst compared with SnS2. The Ni-SnS2-VS monolayer, in particular, exhibits a suitable band alignment that perfectly overcomes the redox potentials for overall water splitting. The dual-defective monolayer displays remarkable photocatalytic activity, a spatially separated carrier, a broadened optical absorption spectrum, and enhanced adsorption energy of H2O. Therefore, the dual-defective SnS2 monolayer can serve as an efficient photocatalyst for overall water splitting to produce hydrogen fuel. Furthermore, a novel dual-defect method can be an effective strategy to enhance the photocatalytic behavior of 2D materials; it may pave inroads in the development of solar-fuel generation.

Thermoelectric (TE) devices used to convert waste heat directly into electricity are highly desirable for alleviating the prevailing energy crisis and global climate-change issues. Among the various TE materials available, metal oxides exhibit high thermal and chemical stabilities in air, and are hence, preferred for use in many TE applications. However, most of them possess TE figures of merit (ZT) that are below the applicable value of 2, in the mid-temperature region (from 250 to 600 °C). In a previous work, the removal of a small amount of Bi from BiCuSeO was found to improve the ZT of BiCuSeO. In this work, we pursue another track and study the TE performance of BiCuTeO after the addition of up to 6% excess Bi. Bi1+xCuTeO (x = 0.00–0.06) samples were prepared by solid-state reactions, followed by hot-pressing to form pellets. By adding a stoichiometric excess of Bi into BiCuTeO, 16% enhancement in power factor was achieved at 450 °C. This enhancement can be attributed to the increase in the Seebeck coefficient because of the appearance of secondary phases. Detailed characterizations and discussions of the effect of the nominal excess Bi in BiCuTeO are presented in this paper. The findings of this study can be applied in the investigation of novel high-performance TE materials.

A highly reproducible sample preparation method for pure GeTe in a rhombohedral structure without converting to the cubic structure up to ∼500 °C is reported to show control of the Ge-vacancy level and the corresponding herringbone-structured microdomains. The thermoelectric figure-of-merit (ZT) for GeTe powder could be raised from ∼0.8 to 1.37 at high temperature (HT) near ∼500 °C by tuning the Ge-vacancy level through the applied reversible in situ route, which made it highly controllable and reproducible. The enhanced ZT of GeTe was found to be strongly correlated with both its significantly increased Seebeck coefficient (∼161 μV K−1 at 500 °C) and reduced thermal conductivity (∼2.62 W m−1 K−1 at 500 °C) for a sample with nearly vacancy-free thicker herringbone-structured microdomains in the suppressed rhombohedral-to-cubic structure phase transformation. The microdomain and crystal structures were identified with HR-TEM (high-resolution transmission electron microscopy) and powder X-ray diffraction (XRD), while electron probe micro-analysis (EPMA) was used to confirm the stoichiometry changes of Ge : Te. Theoretical calculations for GeTe with various Ge-vacancy levels suggested that the Fermi level shifts toward the valence band as a function of increasing the Ge-vacancy level, which is consistent with the increased hole-type carrier concentration (n) and effective mass (m*) deduced from the Hall measurements. The uniquely prepared sample of a near-vacancy-free GeTe in a rhombohedral structure at high temperature favoured an enhanced Seebeck coefficient in view of the converging L- and Σ-bands of the heavy effective mass at the Fermi level, while the high density domain boundaries for the domain of low carrier density were shown to reduce the total thermal conductivity effectively.

BiCuTeO is a potential thermoelectric material owing to its low thermal conductivity and high carrier concentration. However, the thermoelectric performance of BiCuTeO is still below average and has much scope for improvement. In this study, we manipulated the nominal oxygen content in BiCuTeO and synthesized BiCuTeOx (x = 0.94–1.06) bulks by a solid-state reaction and pelletized them by a cold-press method. The power factor was enhanced by varying the nominal oxygen deficiency due to the increased Seebeck coefficient. The thermal conductivity was also reduced due to the decrease in lattice thermal conductivity owing to the small grain size generated by the optimal nominal oxygen content. Consequently, the ZT value was enhanced by ∼11% at 523 K for stoichiometric BiCuTeO0.94 compared to BiCuTeO. Thus, optimal oxygen manipulation in BiCuTeO can enhance the thermoelectric performance. This study can be applied to developing oxides with high thermoelectric performances.

Exploring electrocatalysts composed of earth-abundant elements for a highly efficient hydrogen evolution reaction (HER) is scientifically and technologically important for electrocatalytic water splitting. In this work, we report HER properties of acid treated pyrolyzed vitamin B12 supported on reduced graphene oxide (B12/G800A) that shows an extraordinarily enhanced catalytic activity with low overpotential (115 mV vs. RHE at 10 mA cm−2), which is better than that of most traditional nonprecious metal catalysts in acidic media. Stability tests through long-term potential cycles and at a constant current density confirm the exceptional durability of the catalyst. Notably, the B12/G800A catalyst exhibits extremely high turnover frequencies per cobalt site in acid, for example, 0.85 and 11.46 s−1 at overpotentials of 100 and 200 mV, respectively, which are higher than those reported for other scalable non-precious metal HER catalysts. Moreover, it has been conjectured that the covalency of Co–C and Co–N bonds affects HER activities by comparing the extended X-ray absorption fine structure (EXAFS) spectra of the B12/G800A. High-temperature treatment can modify the Co-corrin structure of B12 to form Co–C bonds along with Co–N, which broadens the band of cobalt, essentially lowering the d-band center from its Fermi level. The lower d-band center leads to a moderate hydrogen binding energy, which is favorable for hydrogen adsorption and desorption.