Kuei-Hsien Chen

As a lead-free high-performance thermoelectric material, germanium telluride (GeTe) has recently been extensively studied for mid-temperature (500–800 K) applications. The carrier concentration and the thermal conductivity are reduced for vacancy-controlled GeTe compounds compared with pristine GeTe. We explored and optimized the Ge0.9−xSb0.1PxTe (x = 0.01–0.05) material's highest thermoelectric performance at elevated temperatures. Intrinsic Ge vacancy control and manipulation of Ge (+2) with Sb/P (+3) increased the charge contribution to power factor improvement to ∼42 µWcm−1 K−2 while minimizing the lattice thermal contribution to ∼0.4 W/mK. This resulted in an increase in thermoelectric performance of ∼2.4 @ 773 K for the Ge0.88Sb0.1P0.02Te sample. The inclusion of atomically disordered Sb/P ions considerably increases the scattering effects caused by the point defect, whereas stretched grain boundaries reveal the decreased lattice thermal contribution. The current work demonstrates the effectiveness of phosphorus as a co-dopant in increasing the average thermoelectric performance (ZTavg) value over the GeTe operating temperature range.

n/a

A fine control of carriers in solids is the most essential thing while exploring any functionality. For a ternary skutterudite like CoSn1·5Te1.5−x, which has been recently recognized as a potential material for thermoelectric conversion, the dominant carrier could be either electrons or holes via chemically tuning the quaternary Sn2Te2 rings in the structure. Both theoretical calculation and different spectroscopic probes, such as X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectroscopy (XAS) were employed to unveil the conduction type switching details. On the other hand, a Ni-for-Co substitution was applied to enhance electronic transport, and thereby the thermoelectric power factor. Thanks to the substantial cut-off of lattice thermal conductivity by the characteristic Sn2Te2 rings in the skutterudite structure, ultimately a 70-fold increase in the dimensionless figure-of-merit (zT) is achieved at 723 K with the nominal composition Co0·95Ni0·05Sn1·5Te1.5.

n/a

Tin monosulfide (SnS) is a promising light-harvesting material for solar cell applications, owing to its potential for large-scale production, cost-effectiveness, eco-friendly source materials, and long-term stability. However, SnS crystallizes in an orthorhombic structure, which results in a highly anisotropic charge transport behavior. Tailoring the crystallographic orientation of the SnS absorber layer plays a critical role in the enhancement of the transfer of charge carriers and the power conversion efficiency (PCE). By controlling the substrate tilting angle and temperature ramp rate in vapor transport deposition, the crystal growth orientation was tuned to a preferred direction which significantly suppressed the unfavorable (040) crystallographic plane. Through the combination of these two approaches, the PCE could be increased from 0.11% to 2%. The effect of the tilting angle was numerically simulated to investigate its role in controlling the film uniformity and directing the film growth. In addition, the correlation between the texture coefficient of the (040) plane and the charge transport properties was determined by a combination of analytical methods such as device performance studies, electrochemical impedance spectroscopy, along with transient photovoltage, space-charge-limited current, and dark current measurements. These techniques were blended together to prove that the marked improvement in PCE can be ascribed to a reduced charge recombination (in both SnS bulk and interfaces) and an enhanced hole mobility.

Direct Z-scheme heterojunctions are widely used for photocatalytic water splitting and CO2 reduction due to facilitating well-separated photogenerated charge carriers and spatial isolation of redox reactions. Here, using a facile two-step hydrothermal and ion-exchange method, we uniformly decorate silver orthophosphate (i.e., Ag3PO4) quantum dots with an average characteristic size of ∼10 nm over tin(iv) sulphide (i.e., SnS2) nanosheets to form a 0D/2D heterojunction. The direct Z-scheme mechanism, i.e. charge transport for efficient electron (from SnS2) and hole (from Ag3PO4) recombination, is confirmed by the following experiments: (i) ultraviolet and X-ray photoelectron spectroscopies; (ii) photodeposition of Pt and PbO2 nanoparticles on reduction and oxidation sites, respectively; (iii) in situ X-ray photoelectron spectroscopy; and (iv) electron paramagnetic resonance spectroscopy. Owing to the photoreduction properties of Ag3PO4 with orthophosphate vacancies, Z-scheme charge carrier transfer, and efficient exciton dissociation, an optimized heterojunction shows a high CO2-to-CO reduction yield of 18.3 μmol g−1 h−1 with an illustrious selectivity of ∼95% under light illumination, which is about 3.0 and 47.8 times larger than that of Ag3PO4 and SnS2, respectively. The carbon source for the CO product is verified using a 13CO2 isotopic experiment. Moreover, by tracing the peak at ∼1190 cm−1 in the dark and under light irradiation, in situ diffuse reflectance infrared Fourier transform spectroscopy demonstrates that the CO2 reduction pathway goes through the COOH* intermediate.

n/a

Multielement alloying is an appealing approach for suppressing thermal conductivity of thermoelectric materials. In this study, we synthesized GeTe-based high-entropy alloys with notable (S, Se) substitution at Te sites and (Ag, Sb) at Ge sites. The Ge0.82Ag0.08Sb0.1S0.5Se0.1Te0.4 exhibits an extremely low thermal conductivity of ∼ 0.66 W/m⋅K and a high Seebeck coefficient (>250 μV/K) over a temperature range of 150 – 400 °C. The influence of lattice distortion on phase transformation and transport properties of Ge0.9-2xAg2xSb0.1S0.5Se0.1Te0.4 (x = 0 – 0.06) was investigated.

Although hematite (i.e., α-Fe2O3) has been widely investigated in photoelectrochemical water oxidation studies due to its high theoretical photocurrent density, it still suffers from serious surface charge recombination and low photoelectrochemical stability. Here we report an in-situ electrochemical method to form a uniform and ultrathin (i.e., 3–5 nm) passivation layer all over the porosities of the optimized ~3.2% Ti-doped α-Fe2O3 photoanode. We unveil the amorphous and defective nature of the in-situ derived layer assigning to a high concentration of oxygen vacancy and intercalated potassium atoms there, i.e., the formation of Ti/K co-doped defective α-Fe2O3-x. Owing to the efficient passivation of surface states, alleviated surface-potential fluctuations, and low charge-transfer resistance at the interface, photoanodes show an average of ~60% enhancement in the photoelectrochemical performance, applied bias absorbed photon-to-current efficiency of 0.43%, and Faradaic efficiency of ~88%. Moreover, the passivation layer prevents direct contact between the electrode material and electrolyte, resulting in less degradation and outstanding photoelectrochemical stability with photocurrent retention of ~95% after ~100 hours, albeit by performing several successive in-situ electrochemical passivation processes. This work presents an industrially scalable method to controllably engineer the interfaces of semiconductors–electrolytes with precious metal-free defective hematite-based co-catalysts for sustainable photoelectrochemical solar-to-fuel conversion applications.

Abstract Effects of electronic and atomic structures of V-doped 2D layered SnS2 are studied using X-ray spectroscopy for the development of photocatalytic/photovoltaic applications. Extended X-ray absorption fine structure measurements at V K-edge reveal the presence of VO and VS bonds which form the intercalation of tetrahedral OVS sites in the van der Waals (vdW) gap of SnS2 layers. X-ray absorption near-edge structure (XANES) reveals not only valence state of V dopant in SnS2 is ≈4+ but also the charge transfer (CT) from V to ligands, supported by V Lα,β resonant inelastic X-ray scattering. These results suggest V doping produces extra interlayer covalent interactions and additional conducting channels, which increase the electronic conductivity and CT. This gives rapid transport of photo-excited electrons and effective carrier separation in layered SnS2. Additionally, valence-band photoemission spectra and S K-edge XANES indicate that the density of states near/at valence-band maximum is shifted to lower binding energy in V-doped SnS2 compare to pristine SnS2 and exhibits band gap shrinkage. These findings support first-principles density functional theory calculations of the interstitially tetrahedral OVS site intercalated in the vdW gap, highlighting the CT from V to ligands in V-doped SnS2.

In this work, we study the effect of sputtering pressures on the thermoelectric properties of GeTe films. The working pressures were differentiated from 3 to 30 mTorr, and the as-deposited films were annealed at 623 K for 10 min in Ar atmosphere. The results show that the working pressure has a significant effect on the Ge content and crystalline size. The turning trend of the Seebeck coefficient with different sputtering pressures corresponds to the Ge content. The surface morphology of annealed film will change from cracks to voids with increasing sputtering pressure. This behavior can be explained by the growth mechanisms model. The voids and relatively low crystalline size of GeTe films affect to the reduction of the electrical conductivity. In addition, the void content decreased as film thickness was increased. Therefore, controlling the working pressures in the sputtering process and film thickness is important for the thermoelectric performance of GeTe thin film. In our work, we prove that the thermoelectric properties of GeTe films could be optimized effectively by simply tuning different sputtering conditions.

Exploring an efficient platinum group metal (PGM) free electrocatalyst with superior activity and stability for hydrogen evolution reaction (HER) in a wide pH range is desirable for low-cost hydrogen production. Here, we report atomically dispersed cobalt on nitrogen and sulfur co-doped graphene (N-Co-S/G) for HER. Remarkably, the prepared N-Co-S/G electrocatalyst shows a small overpotential of 67.7 mV vs. reversible hydrogen electrode (RHE) at a current density of 10 mA cm−2 and exceptional durability over 100 h at 10 mA cm−2 under acidic conditions. Moreover, we found that the HER activity of N-Co-S/G is close to 20% Pt/C at all pH levels (0–14) and superior activity at high current density (>100 mA cm−2). Experimental and theoretical calculations reveal that the S atom in N-Co-S/G form Co-S bond, resulting new Co-N3S1 active site, which optimizes Gibbs free energy for hydrogen adsorption (∆GH*) close to zero, while water adsorption and dissociation enhanced by S modulation for neutral and basic media HER.

Pharmaceutical drugs' removal from wastewater by photocatalytic oxidation process is considered as an attractive approach and environmentally friendly solution. This report aims to appraise the practical application potential of Ag/g-C3N4/ZnO nanorods toward the wastewater treatment of the pharmaceutical industry. The catalysts are synthesized by straightforward and environmentally-friendly strategies. Specifically, g-C3N4/ZnO nanorods heterostructure is constructed by a simple self-assembly method, and then Ag nanoparticles are decorated on g-C3N4/ZnO nanorods by a photoreduction route. The results show that three commercial drugs (paracetamol, amoxicillin, and cefalexin) with high concentration (40 mg L−1) are significantly degraded in the existence of a small dosage of Ag/g-C3N4/ZnO nanorods (0.08 g L−1). The Ag/g-C3N4/ZnO nanorods photocatalyst exhibits degradation performance of paracetamol higher 3.8, 1.8, 1.3 times than pristine g-C3N4, ZnO nanorods, and g-C3N4/ZnO nanorods. Furthermore, Ag/g-C3N4/ZnO nanorods have an excellent reusability and a chemical stability that achieved paracetamol degradation efficiency of 78% and remained chemical structure of the photocatalyst after five cycles. In addition, the photocatalytic mechanism explanation and comparison of photocatalytic drugs’ degradation ability have also been discussed in this study.

Solar cells based on kesterite Cu2ZnSnSe4 (CZTSe) compounds with earth-abundant elements are highly desirable for the low-cost and high-efficiency production of renewable energy. However, the occurrence of intrinsic defects substantially impairs the photovoltaic properties of CZTSe. Herein, a cation substitution method to control and passivate the defect states in bandgap of kesterite CZTSe by incorporating Ag ions is introduced. Intensity-dependent low-temperature photoluminescence measurements show that Ag incorporation can reduce the density and depth of intrinsic defects in CZTSe. The results reveal that 10% Ag-alloyed CZTSe provides the shallowest defect states and less nonradiative recombination. It is also confirmed by first-principles calculations that Ag incorporation enables the formation and suppresses the beneficial and detrimental defects, respectively. Based on the theoretical results, the observed subband photoluminescence peaks can be assigned to the intrinsic point and cluster defects. The best power conversion efficiency of 10.2% is achieved for the 10% Ag-alloyed CZTSe cell, along with an enhanced open-circuit voltage. These results open up a new avenue for further improving the performances of CZTSe-based device via defect engineering.

Utilization of g-C3N4 as a single photocatalyst material without combination with other semiconductor remains challenging. Herein, we report a facile green method for synthesizing a metal free modified g-C3N4 photocatalyst. The modification process combines four different strategies in a one-pot thermal reaction: non-metal doping, porosity generation, functionalization with amino groups, and thermal oxidation etching. The as-prepared amino-functionalized ultrathin nanoporous boron-doped g-C3N4 exhibited a high specific surface area of 143.2 m2 g−1 which resulted in abundant adsorption sites for CO2 and water molecules. The surface amino groups act as Lewis basic sites to adsorb acidic CO2 molecules, which can also serve as active sites to facilitate hydrogen generation. Besides, the simultaneous use of ammonium chloride as a dynamic gas bubble template along with thermal oxidation etching efficiently boosts the delamination of the g-C3N4 layers to produce ultrathin sheets; this leads to stronger light–matter interactions and efficient charge generation. Consequently, the newly modified g-C3N4 achieved selective gas-phase CO2 reduction into CO with a production yield of 21.95 µmol g-1, in the absence of any cocatalyst. Moreover, a high hydrogen generation rate of 3800 µmol g-1 h-1 and prominent apparent quantum yield of 10.6% were recorded. This work opens up a new avenue to explore different rational modifications of g-C3N4 nanosheets for the efficient production of clean energy.

Cu2ZnSnS4 (CZTS) has demonstrated excellent performance as an anode material for lithium-ion batteries. However, the repeated lithiation and delithiation create a cracking pattern and lead to island formation in the thin-film electrode, resulting in a capacity fading over cycling in lithium-ion batteries (LIB's). In order to control this crack behaviour, we introduce carbon into CZTS thin-films by a hydrothermal method to form CZTS@C composite. CZTS@C significantly reduced the crack pattern formation on the electrode surface as well as improved the conductivity of the CZTS@C electrode. At the early stages of lithiation and delithiation, the volume expansion and contraction of Li–CZTS@C create intra-granular cracking only at the surface level, and it offers a high capacity of about 785 mA h g−1 after 150 cycles at 1000 mA g−1 charging rate, excellent rate capability (942 mA h g−1, 678 mA h g−1 and 435 mA h g−1 at 500 mA g−1, 2000 mA g−1 and 5000 mA g−1), and superior cyclability (925 mA h g−1 even after 200 cycles at 500 mA g−1). The excellent electrochemical performance at high-current rates can be attributed to intra-granular cracking together with carbon coating that provides a short transportation length for both lithium ions and electrons. Moreover, the controlled cracking pattern formation in CZTS@C facilitates faster reaction kinetics, which open up a new solution for the development of high-power thin-film anodes for next-generation LIBs applications.

Layered MoS2 is considered as one of the most promising two-dimensional photocatalytic materials for hydrogen evolution and water splitting; however, the electronic structure at the MoS2-liquid interface is so far insufficiently resolved. Measuring and understanding the band offset at the surfaces of MoS2 are crucial for understanding catalytic reactions and to achieve further improvements in performance. Herein, the heterogeneous charge transfer behavior of MoS2 flakes of various layer numbers and sizes is addressed with high spatial resolution in organic solutions using the ferrocene/ferrocenium (Fc/Fc+) redox pair as a probe in near-field scanning electrochemical microscopy, i.e. in close nm probe-sample proximity. Redox mapping reveals an area and layer dependent reactivity for MoS2 with a detailed insight into the local processes as band offset and confinement of the faradaic current obtained. In combination with additional characterization methods, we deduce a band alignment occurring at the liquid-solid interface.

Abstract Sulfonated polyaryletherketones (SPAEK) bearing four sulfonic acid groups on the phenyl side groups were synthesized. The benzophenone moiety of polymer backbone was further reduced to benzydrol group with sodium borohydride. The membranes were crosslinked by acid-catalyzed Friedel-Crafts reaction without sacrifice of sulfonic acid groups and ion exchange capacity (IEC) values. Crosslinked membranes with the same IEC value but different water uptake could be prepared. The optimal crosslinking condition was investigated to achieve lower water uptake, better chemical stability (Fenton's test), and higher proton conductivity. In addition, the hydrophilic ionic channels from originally course and disordered could be modified to be narrow and continuous by this crosslinking method. The crosslinked membranes, CS4PH-40-PEKOH (IEC = 2.4 meq./g), reduced water uptake from 200 to 88% and the weight loss was reduced from 11 to 5% during the Fenton test compared to uncrosslinked one (S4PH-40-PEK). The membrane showed comparable proton conductivity (0.01?0.19?S/cm) to Nafion 212 at 80°C from low to high relative humidity (RH). Single H2/O2 fuel cell based on the crosslinked SPAEK with catalyst loading of 0.25?mg/cm2 (Pd/C) exhibited a peak power density of 220.3 mW/cm2, which was close to that of Nafion 212 (214.0 mW/cm2) at 80°C under 53% RH. These membranes provide a good option as proton exchange membrane with high ion exchange capacity for fuel cells.

Tin-based composites are promising anode materials for high-performance lithium-ion batteries (LIBs); however, insufficient conductivity, as well as fatal volume expansion during cycling lead to poor electrochemical reversibility and cycling stability. In this work, we demonstrate the lithium-ion storage behaviors of SnS2 anode material deposited on different electrode supports. The SnS2 grown on 3D hierarchical carbon nanotube-carbon cloth composites (SnS2-CNT-CC) shows superior capacity retention and cycle stability, compared to that on planar Mo sheets and carbon cloth. The specific capacity of SnS2 on Mo, CC, and CNT-CC is around 240, 840, and 1250 g−1, respectively. The SnS2-CNT-CC electrode outperforms in the cyclic performance and rate capability compared to other electrode configurations due to the multi-electron pathway and high surface area derived from 3D hierarchical CNT-CC electrode support. Furthermore, a significant decrease in the charge transfer resistance is observed by utilizing 3D hierarchical CNT-CC electrode support. The use of 3D hierarchical structures as electrode support could be the best alternative to enhance the electrochemical performances for the next generation LIBs.

Abstract A heterobimetallic corrole complex, comprising oxygen reduction reaction (ORR) active non-precious metals Co and Fe with a corrole-N4 center (PhFCC), is successfully synthesized and used to prepare a dual-atom molecular catalyst (DAMC) through subsequent low-temperature pyrolysis. This low-temperature pyrolyzed electrocatalyst exhibited impressive ORR performance, with onset potentials of 0.86 and 0.94 V, and half-wave potentials of 0.75 and 0.85 V, under acidic and basic conditions, respectively. During potential cycling, this DAMC displayed half-wave potential losses of only 25 and 5 mV under acidic and alkaline conditions after 3000 cycles, respectively, demonstrating its excellent stability. Single-cell Nafion-based proton exchange membrane fuel cell performance using this DAMC as the cathode catalyst showed a maximum power density of 225 mW cm−2, almost close to that of most metal–N4 macrocycle-based catalysts. The present study showed that preservation of the defined CoN4 structure along with the cocatalytic Fe–Cx site synergistically acted as a dual ORR active center to boost overall ORR performance. The development of DAMC from a heterobimetallic CoN4-macrocyclic system using low-temperature pyrolysis is also advantageous for practical applications.

The thickness of transition metal dichalcogenides (TMDs) plays a key role in enhancing their photocatalytic CO2 reduction activity. However, the optimum thickness of the layered TMDs that is required to achieve sufficient light absorption and excellent crystallinity has still not been definitively determined. In this work, ultra-thin molybdenum disulfide films (MoS2TF) with 25 nm thickness presented remarkable photocatalytic activity, and the product yield increased by about 2.3 times. The photocatalytic mechanism corresponding to the TMDs’ thickness was also proposed. This work demonstrates that the thickness optimization of TMDs provides a cogent direction for the design of high-performance photocatalysts.